SSL II® with ASJ Max Fiberglas™ Pipe Insulation

Owens Corning® Fiberglas™ Pipe Insulation is molded of heavy density resin bonded inorganic glass fibers that come in one-piece, 36" (914mm) long, hinged sections. Sections can be ordered as factory applied SSL II® with ASJ Max or as unjacketed No-Wrap.

Fiberglas Pipe Insulation Portfolio Brochure PDF | 4.59 MB

Owens Corning® Fiberglas™ Pipe Insulation is molded of heavy density resin bonded inorganic glass fibers that come in one-piece, 36" (914mm) long, hinged sections. Sections can be ordered as factory applied SSL II® with ASJ Max or as unjacketed No-Wrap.

Fiberglas Pipe Insulation Portfolio Brochure PDF?V=1523505902000 | 4.59 MB

Specifications and Literature

Product Features

Durability

The SSL II® positive closure system was designed with advanced adhesives to work specifically with the ASJ Max jacket to provide a tight, reliable seal that doesn’t need glue or staples. It also has a higher puncture resistance and less wicking/curling than standard ASJ.

Easy Installation

Mold and Mildew Resistance

Durable, cleanable, all-service-jacket with polymer film exterior surface doesn’t support mold or mildew growth.

Certifications

Technical Information

Physical Properties

PropertyTest MethodValue
Density(size dependent)ASTM C3023.5 to 5.5 pcf
Operating Temperature Range15ASTM C4110В°F to 1,000В°F(-18В°C to 538В°C)16
Water Vapor SorptionASTM C1104Less than 5% by weight
CorrosionASTM C665Pass - steel, copper, or aluminum
Jacket Temperature LimitationASTM C1136-20В°F to 150В°F (-29В°C to 66В°C)
Jacket PermeanceASTM E96, Proc. A0.02 perm
Burst Strength, minASTM D774/D774M100 psi
Composite Surface Burning Characteristics17UL 723, ASTM E84 or CAN/ULC-S102Flame Spread 25
Smoke Developed 50

Standards Codes Compliance

  • ASTM C547, Mineral Fiber Pipe Insulation, Types I and IV
  • ASTM C585, Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
  • ASTM C1136, Flexible Low Permeance Vapor Retarders for Thermal Insulation: Types I, II, III, IV
  • ASTM C795, Thermal Insulation for Use in Contact with Austenitic Stainless Steel18
  • MIL-PRF-22344E, Insulation, Pipe, Thermal, Fibrous Glass
  • Nuclear Regulatory Commission Guide 1.36, Non-Metallic Thermal Insulation18
  • MIL-DTL-24244D (Ships) Insulation Material with Special Corrosion, Chloride, and Fluoride Requirements18
  • US Coast Guard 164.109/70/0 Non-Combustible (No-Wrap only)
  • NFPA 90A and 90B

1. The surface burning characteristics of these products have been determined in accordance with UL723, ASTM E84, or CAN/ULC-S102. These standards should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, the results of these tests may be used as elements of a fire risk assessment that takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest 5 rating.

2. Includes core weight.

3. Includes core weight

4. Sample modified as required to meet applicable test method.

5. XPS foam core values meet ASTM C578 TYPE IV.

6. k means the apparent thermal conductivity. The lower the value, the greater the insulation power.

7. Values at yield or 10% deflection, whichever occurs first.

8. Data ranges from 0.00 to value shown due to the level of precision of the test method.

9. Water vapor permeance decreases as thickness increases.

10. These laboratory tests are not intended to describe the hazard presented by this material under actual fire conditions.

11. Fire performance of FOAMULAR® 4" thick product only. Thicker products may have different fire performance characteristics. Due to limits on the equipment used to test per ASTM E84, Owens Corning® FOAMULAR® XPS Fabrication Billets have not been tested.

12. Limited to single layer application.

13. The surface burning characteristics of these products have been determined in accordance with ASTM E84. This standard should be used to measure and describe the properties of materials, products or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest 5 rating.

14. Preproduction qualification testing complete and on file. Chemical analysis of each production lot required for total conformance.

15. Limited to single layer applications above 650°F (343°C), but not greater than 6" (152mm) thickness.

16. With heat up schedule.

17. The surface burning characteristics of these products have been determined in accordance with UL 723, ASTM E84 or CAN/ULC-S102. Values are reported to the nearest 5 rating.

18. Preproduction qualification testing

Applicable Standards

  • SCS Recycled Content - Average 53%
  • UL Greenguard Gold

eBooks and Guides

Division 22/23 eBook

The Division 22/23 Mechanical Manufacturer’s Guide eBook is an easy-to-use tool that can be accessed anytime, anywhere to view duct, pipe and HVAC equipment insulation solutions, product data sheets, CSI MasterFormat® three-part system specifications and green building program guides.

3E Plus®

Owens Corning is proud to partner with 3E Plus® to deliver answers about using our insulation products in your business applications.

You can also download the 3E Plus® User Guide for any questions.

Find our Products

Find a Professional

CONTACT US

Even though we’re a global company, we’re always ready to answer your questions. Call to speak with an Owens Corning representative so you can start your project right away.

1-800-GET-PINK